egghelp/eggheads community

Setting User in User File

2009-03-25T16:03:21-04:00

Wow. I must have read over that setting like a 1000 times .

Thank you.

Statistics: Posted by rrc55 — Wed Mar 25, 2009 4:03 pm

Setting User in User File

2009-03-25T15:22:20-04:00

Maybe you've setuped global ban-time 120?Put it to 0,and change it from 120 to 0 for every channel =)

Statistics: Posted by DaRkOoO — Wed Mar 25, 2009 3:22 pm

Setting User in User File

2009-03-25T00:56:27-04:00

Just one last problem. I just noticed that my bot automatically removes bans in the channel. I can't figure out what setting would stop this. I have enforcebans and most of my channel set settings turned off in my config. It has a mind of its own. Please help. Thanks.

Statistics: Posted by rrc55 — Wed Mar 25, 2009 12:56 am

Setting User in User File

2009-03-21T14:38:32-04:00

Sorry, my bad, was supposed to write disconnect_server(). You'll find it in the same file though.. I'll update my previous post as well. And you could add the line pretty much anywhere within the function, I'd suggest in the end.

And yes, you edit the file, and recompile.

Statistics: Posted by nml375 — Sat Mar 21, 2009 2:38 pm

Setting User in User File

2009-03-21T13:16:41-04:00

So edit the source code and recompile? I'm scared.

I found this towards the end of the function:

Code:

if (server_cycle_wait)      /* Back to 1st server & set wait time.       * Note: Put it here, just in case the server quits on us quickly       */      cycle_time = server_cycle_wait;    else      cycle_time = 0;

Could I just replace the else statement or should I replace the entire if statement or should I add it somewhere else?

Thank you kind sir

Statistics: Posted by rrc55 — Sat Mar 21, 2009 1:16 pm

Setting User in User File

2009-03-21T14:40:39-04:00

*Vrrz* Secret code Accepted! *beep*

Did some digging, and unfortunately, the time specified in the server-cycle-wait setting only affects the time in between connection attempts, not between disconnect and reconnect.
There is, unfortunately, no way of delaying new server connections from the disconnect without editing the source code. One simple hack, that I believe would do the trick would be to add a line like below to the function disconnect_server() in file src/mod/server.mod/servmsg.c:

Code:

 cycle_time = server_cycle_wait;

Edit: Fixed minor brainfart.. (it's disconnect, not connect)

Statistics: Posted by nml375 — Sat Mar 21, 2009 12:05 pm

Setting User in User File

2009-03-21T10:33:51-04:00

pretty please with a cherry ontop

Statistics: Posted by rrc55 — Sat Mar 21, 2009 10:33 am

Setting User in User File

2009-03-16T18:40:06-04:00

Statistics: Posted by rrc55 — Mon Mar 16, 2009 6:40 pm

Setting User in User File

2009-03-15T20:41:32-04:00

Hmm..
Think I'll have to dig into the code to check/verify that one :/

Statistics: Posted by nml375 — Sun Mar 15, 2009 8:41 pm

Setting User in User File

2009-03-15T14:01:51-04:00

I believe this is what you are looking for:

Code:

# This setting defines how long Eggdrop should wait before moving from one# server to another on disconnect. If you set 0 here, Eggdrop will not wait# at all and will connect instantly. Setting this too low could result in# your bot being K:Lined.set server-cycle-wait 60

Turns out that setting doesn't do it. When I get disconnected form a server, eggdrop immediately tries to reconnect to it. I set it to 300.

I think what's happening is that it waits the 5 minutes to reconnect only when my internet connection isn't immediately available. If the connection to the server gets dropped for whatever reason, but my connection is immediately available, it goes ahead and reconnects right away.

Statistics: Posted by rrc55 — Sun Mar 15, 2009 2:01 pm

Setting User in User File

2009-03-14T03:39:40-04:00

Figured that was probably it. Thanks again.

Statistics: Posted by rrc55 — Sat Mar 14, 2009 3:39 am

Setting User in User File

2009-03-13T17:50:25-04:00

I believe this is what you are looking for:

Code:

# This setting defines how long Eggdrop should wait before moving from one# server to another on disconnect. If you set 0 here, Eggdrop will not wait# at all and will connect instantly. Setting this too low could result in# your bot being K:Lined.set server-cycle-wait 60

Statistics: Posted by nml375 — Fri Mar 13, 2009 5:50 pm

Setting User in User File

2009-03-13T15:44:07-04:00

Is there any way to delay the reconnecting of my bot to a server upon a disconnect?

Statistics: Posted by rrc55 — Fri Mar 13, 2009 3:44 pm

Setting User in User File

2009-03-13T02:27:39-04:00

That was the problem. Forgot I had changed the default hello to something else.

Thank you so much.

Statistics: Posted by rrc55 — Fri Mar 13, 2009 2:27 am

Setting User in User File

2009-03-12T16:08:32-04:00

Could you check this part in your config file?

Code:

# Many IRCops find bots by seeing if they reply to 'hello' in a msg.# You can change this to another word by un-commenting the following# two lines and changing "myword" to the word wish to use instead of# 'hello'. It must be a single word.#unbind msg - hello *msg:hello#bind msg - myword *msg:hello

Specifically, that there is indeed a # in front of the last two lines?

Statistics: Posted by nml375 — Thu Mar 12, 2009 4:08 pm