egghelp/eggheads community

AFP Problem

2006-04-29T09:41:29-04:00

If you want the same settings on #chan1 to be on #chan2, then use the ap:import DCC command.

.ap:import #chan1 #chan2

and all settings on #chan1 will be set on #chan2.

Statistics: Posted by Sir_Fz — Sat Apr 29, 2006 9:41 am

AFP Problem

2006-04-29T09:33:22-04:00

Ok, once this is done are the settings stored in a file somewhere so I can copy/paste them into another file and change the channel name so I don't have to redo the settings all over again?

Statistics: Posted by dq — Sat Apr 29, 2006 9:33 am

AFP Problem

2006-04-29T09:32:08-04:00

Unfortunatly you have to disable each setting manually (i.e. .chanset #channel setting1 0:0 or - for each setting).

Statistics: Posted by Sir_Fz — Sat Apr 29, 2006 9:32 am

AFP Problem

2006-04-29T09:30:26-04:00

Ok sounds good, but if I wanted to do it now.. could you briefly explain?

Statistics: Posted by dq — Sat Apr 29, 2006 9:30 am

AFP Problem

2006-04-29T09:29:27-04:00

In v4.6 which is coming soon, I have a new command ap:disable which will allow you to disable AP on a channel or on all channels.

Statistics: Posted by Sir_Fz — Sat Apr 29, 2006 9:29 am

AFP Problem

2006-04-29T09:26:51-04:00

Ok, that worked.. but say I wanted EACH setting for the 1 channel turned off apart from 1 or 2?

Statistics: Posted by dq — Sat Apr 29, 2006 9:26 am

AFP Problem

2006-04-29T09:16:33-04:00

Well, you don't have to edit each setting for each channel. You can use '*' via .chanset, example:

.chanset * ap:textl 5:2

this will change this setting on all channels. And it will never change unless you change it (same as the default settings, they remain the same untill you edit them).

Statistics: Posted by Sir_Fz — Sat Apr 29, 2006 9:16 am

AFP Problem

2006-04-29T09:10:57-04:00

Is there a way to make them sticky, and yes I know you can edit them via DCC, but I don't wanna have to edit each setting for the 1 channel, it would be extreamly handy if I could make it 'sticky' via the script.

Statistics: Posted by dq — Sat Apr 29, 2006 9:10 am

AFP Problem

2006-04-29T09:07:15-04:00

This is the dafault setting, which means that it is set on channels where you haven't edited the AP settings yet. For example, if you load the script for the first time, all channels will have these default settings but when you change these settings, the default setting will not apply on them anymore (that's why they're called default and not sticky).

Edit: I assume you know that these settings can be edited via DCC right? (i.e. .chanset #channel ap:textl 5:2)

Statistics: Posted by Sir_Fz — Sat Apr 29, 2006 9:07 am

AFP Problem

2006-04-29T09:07:28-04:00

With the AllFloodProtection script, It seems when I try to set ANY of the functions to - or 0:0 via the .tcl it ignores it, sure it works when you disable it thru DCC chat but say I wanted a large veriarty of the script disabled but NOT removed how would you do this?

# use .chanset #channel ap:textl : (in DCC, 0:0 to disable)
# Set default rate here:
lappend ap:udefs {ap:textl 5:2}

It says, set default here but if I wanted the default to 0:0 it ignores it.

Sir_Fz care to help

Statistics: Posted by dq — Sat Apr 29, 2006 8:56 am